barcodeanna.blogg.se - Renogy wanderer manual

Renogy wanderer manual how to#
Renogy wanderer manual install#
Renogy wanderer manual password#
Renogy wanderer manual Bluetooth#

If the battery light is slow flashing red, it means the battery is over-heating. It will apply a small charge current to activate the lithium battery protection circuit and if a correct cell voltage can be reached, it starts a normal charge.

The Wanderer PWM charge controller has a reactivation feature to awaken a sleeping Lithium battery. The protection circuit of a lithium battery typically turns the battery off and makes it unusable if over-discharged. This can happen when storing a lithium battery pack in a discharge state for any length of time as self-discharge would gradually deplete the remaining charge. If the battery indicator on your charge controller is solid red, this means the battery is over-discharged. Renogy Wanderer Charge Controller Battery Light Red If this is the case, simply disconnect the PV panels and switch them. To troubleshoot, check the voltage at the PV terminal using a multi-meter and see if you get a negative reading. The most likely reason the PV light on your Renogy Wanderer is not turning on is you have reverse polarity. If the PV light on your controller is slow flashing green and the battery indicator is slow flashing green, it shows the battery is in float charge. If the PV light is slow flashing green and the battery indicator is solid green, it shows the battery is charging normally. Ensure that they meet the specification of the controller to not exceed 25 VDC. Use a multi-meter to check the voltage of the panels.To troubleshoot PV is over-voltage, follow these instructions:

When the PV light on your Renogy Wanderer charge controller is fast flashing green, it indicates the PV terminal is over-voltage.

Renogy wanderer manual how to#

This indicates the parameter has been set.Ĭheck this too: Victron Energy MPPT Solar Charge Controller How to & Troubleshooting Guide Renogy Wanderer Solar Charge Controller PV Light Flashing Once flashing, then press the gray button again to the desired battery type (they are color-coded) and simply leave the controller alone until the flashing stops (this should take about 10 seconds). To set battery type, simply hold the gray button for approximately 7 seconds until the LED flashes.

After setting parameters, click “Set”, then “Set successful” will pop up, indicating the parameters have been saved successfully.

Renogy wanderer manual password#

You will get a notification after verifying password and setting parameters.

The admin password for configuration is “135790123”.

Then you can change battery and load configuration.

Click “Read”, you will be notified after read parameters successfully.

By clicking the “>” below, you can read the data on graphs.

By clicking the “Last Day” on the top left and “Next Day” on the top right, you can read daily history data of the controller.

You can monitor the real-time performance of solar panel, battery and load.

After successfully connecting to the device, switch to “Monitoring” using the bottom bar.

To program a Renogy Wanderer charge controller using Renogy BT App, follow the instructions below:

Renogy wanderer manual Bluetooth#

How to Program a Renogy Wanderer Solar Charge Controller (with and without Bluetooth App) You can also see device information on the screen.

After connecting successfully, device status will change to “Device connecting”.

Remember to turn on Bluetooth on your smartphone.

Open the Renogy BT App, select “Device Info”, then click ‘Search Device”.

Renogy wanderer manual install#

Download Renogy BT app from Google Play Store or App Store, and install it on your device.To connect the Wanderer to your smart phone: After pairing is done you can then monitor your system and change parameters directly from your smart phone or tablet. The BT-1 Bluetooth module is a great addition to Renogy charge controllers with RS232 and RJ12 ports and is used to pair charge controllers with the Renogy BT App. To connect a Renogy Wanderer solar charge controller to a smartphone, you will need the BT-1 Bluetooth Module which is sold separately. How to Connect a Renogy Wanderer Solar Charge Controller to a Smartphone In this how-to and troubleshooting guide, learn how to fix common Renogy Wanderer solar charge controller issues and perform various operations. It is recommended to perform some basic troubleshooting procedures to resolve Issues with these charge controllers, before calling for repairs or ordering a replacement. Renogy Wanderer solar charge controllers are among the best in market, featuring impressive features and designs.